-
-
If the DR-L connectors have a second crimping point in the component application, they can be used on solid conductors. Since the DR connectors are designed shorter and only allow one crimping point, the component application cannot be used for solid conductors. The common crimping pliers have 2 crimping points in the jaws, i.e. on the DR-L, the pliers are applied 2x for left and right. On the DR, the pliers are pressed on both sides with 1x pressing operation. The EASY-FIX system application is in turn available on solid conductors.
-
-
Hiermit teilen wir Ihnen mit, dass unsere Produkte (Erzeugnisse) mit dem SVHC-Stoff Blei (CAS 7439-92-1) in der Konzentration höher als 0,1 % in der SCIP-Datenbank bei der ECHA (Europäische Chemikalienagentur) angemeldet sind. Die Produkte erhalten Aluminium- und/oder Kupferlegierungen in unserer Verbindungstechnik und wurden in der aktuellen REACH-Konformitätserklärung zur Richtlinie EG/1907/2006 vom 28.02.2022 erwähnt. Sie dürfen weiterhin verkauft werden und unterliegen keinem Verkaufsverbot. Die SCIP-Datenbanknummer ist datenrechtlich geschützt und wird hier nicht aufgeführt.
Der Grund zur Einführung der SCIP-Datenbank ist in der Richtlinie (EU) 2018/851, Absatz 38 beschrieben: „Wenn Produkte, Materialien und Stoffe zu Abfall werden, kann es sein, dass diese Abfälle des Vorhandenseins gefährlicher Stoffe nicht zum Recycling oder zur Herstellung hochwertiger Sekundärrohstoffe geeignet sind. Daher müssen im Einklang mit dem Siebten Umweltaktionsprogramm, in dem die Entwicklung schadstofffreier Materialkreisläufe vorgesehen ist, Maßnahmen gefördert werden, durch die der Gehalt an gefährlichen Stoffen in Materialien und Produkten, auch recycelten Materialien, verringert wird, und es muss dafür gesorgt werden, dass während des gesamten Lebenszyklus der Produkte und Materialien ausreichend Informationen über das Vorhandensein gefährlicher Stoffe und insbesondere besonders besorgniserregender Stoffe bereitgestellt werden. Damit diese Ziele verwirklicht werden, muss das Recht der Union für Abfälle, Chemikalien und Produkte besser aufeinander abgestimmt und die Europäische Chemikalienagentur einbezogen werden, um sicherzustellen, dass die Informationen über das Vorhandensein besonders besorgniserregenden Stoffen während des gesamten Lebenszyklus der Produkte und Materialen, auch in der Abfallphase, bereitgestellt werden.“
-
-
The contact pin can be removed with a long socket, which makes it possible to reuse it. We recommend using an additional set, because the surfaces are both cleaned and the lubricant GM1 must be reused. It is also important to ensure appropriate air-release during installation on the feed-through and the termination insert. The required torque is available on request.
-
-
The screw cable lugs of the connector product range are not suitable for this application. This type of cable is very special and requires deeper inspection for suitability.
-
-
The tensile strength of BBC Cellpack sets depends on the system used (e.g.: shell with mounting, screwed connection, tensile connectors). The standard for sets does not include a tensile test of the installed joint. The standard for compression and screw connectors refers to DIN EN 61238-1, which describes the requirements for mechanical testing. A strain relief implies that no tensile forces are applied.
-
-
The conductor shapes are tested at the factory: RE (round, solid), RM (round, stranded), SE (sector, solid) and SM (sector, stranded). Connectors and cable lugs are approved for conductor class 1 (solid conductor construction) and 2 (stranded conductor construction). Compressed conductors (RMv and SMv) are also supported. There is no approval available for class 5 (fine stranded conductors) and class 6 (extra fine stranded conductors).
-
-
BBC Cellpack's AK screw branch clamps are suitable for branching aluminium or copper conductors. To ensure that no parts are lost, we recommend that you only open the AK clamp after the cable ends have been prepared. This is done by stripping the main conductor in the contact area without cutting the conductor. The conductor of the branch is also stripped at the end and then placed above the main conductor. To open the AK clamp, remove the contact screw and the upper plastic half. The AK clamp is assembled in the reverse order.
Two aluminium or two copper conductors can also be connected, but aluminium and copper cannot be combined due to the design.
-
-
BBC Cellpack's FK overhead line terminals are suitable for branching copper conductors. To ensure that no parts are lost, we recommend that you only open the FK terminal after the cable ends have been prepared. This is done by stripping the main conductor in the contact area without cutting the conductor. The conductor of the branch is also stripped at the end and then placed above the main conductor. To open the FK clamp, remove the nut. The FK clamp is assembled in the reverse order. Two copper conductors can also be connected.
-
-
BBC Cellpack's KP branch clamps are suitable for branching copper conductors. To open the KP clamp, turn the screw to the end of the thread. The main cable and the branch cable are then positioned in the housing recesses provided for this purpose without stripping them. To assemble the KP clamp, the screw is tightened again, while the wires are contacted by the integrated cutting contact.
-
-
Yes, CHE/CAE cable terminations can be used with class 5 & 6 conductors according to the cross-section ranges specified in the data sheet. Use cable lugs that are suitable for this class of conductor. CHESK/CAESK cable terminations are differentiated from CHE/CAE by the screw cable lug in the kit. They may not be used with class 5 & 6 conductors.
-
-
When assembling screw connectors and screw cable lugs, forces occur which can no longer be compensated manually. As a result, deformations can occur in the transition area. Deformations can impair the function of the set and damage the conductor material. We recommend using a counter-holder, because of its leverage effect with various tools.
-
-
If a cable lug is not already supplied by BBC Cellpack, it should be selected according to specific criteria. In addition to the conductor (material, cross section, shape), the length and diameter of the hole, the longitudinal watertightness is particularly important. This is due to the fact that the set is directly exposed to environmental influences (such as rain).
-
-
Compression cable lugs according to DIN 46235 and compression connectors according to DIN 46267 are generally suitable for a hexagonal compression of class 5 and 6 conductors (DIN/IEC 60228), this can be verified in a separate test sequence (e.g.: DIN IEC 61238).
-
-
For concentric conductors (without a fixed conductor shape), compression connectors tested according to DIN 46267 can be used. Screw solutions are also possible, but they must first be checked for suitability.
-
-
Standard over-the-counter crimping pliers can be used for insulated connectors. Please enquire with the manufacturer of your choice.
-
-
- The tools in the table have been tried and tested as assembly tools. A manufacturer-independent release of impact wrenches is not possible according to the current status, since only tested devices can be released (product liability).
- Notes on assembly: The tools must not have any defects and must be used properly and according to the enclosed instructions. They must also be positioned correctly and perpendicular to the shear bolt.
- There must be no leverage effect on the shear bolt. Suitable tool inserts (one-piece) must be used. The battery must be sufficiently charged. The assembly must be carried out according to the assembly instructions. The connectors or cable lugs must be approved for the respective application.
Approved screw connectors and cable lug types from | Tool type |
---|
BBC Cellpack | - TYCO IT-1000-023 (manufacturer: Hitachi)
- TYCO IT-1000-033 (manufacturer: Hitachi)
- ASKO compact type BTW 250 FRE (manufacturer: Makita)
- ASKO professional type BTW 151 RJEX (manufacturer: Makita)
- Pfisterer type C18 IW (manufacturer: Milwaukee)
- Type PIW 14.4 SD ½" (manufacturer: Milkauwee)
|
Arcus | - TYCO IT-1000-023 (manufacturer: Hitachi)
- TYCO IT-1000-033 (manufacturer: Hitachi)
- ASKO compact type BTW 250 RFE (manufacturer: Makita)
- ASKO professional type BTW 151 RJEX (manufacturer: Makita)
- Pfisterer type C18 IW (manufacturer: Milwaukee)
|
GPH | - TYCO IT-1000-023 (manufacturer: Hitachi)
- TYCO IT-1000-033 (manufacturer: Hitachi)
- ASKO professional type BTW 151 RJEX (manufacturer: Makita)
- ASKO compact type BTW 250 … (manufacturer: Makita)
- ASKO compact type DTW 250 … (manufacturer: Makita)
- ASKO compact type DTW 280 … (manufacturer: Makita)
- ASKO compact type DTW 285 … (manufacturer: Makita)
- Pfisterer type C18 IW (manufacturer: Milwaukee)
|
| |